TGX20 DSP power amplifier 4 x 5000w, live

TGX20 DSP power amplifier 4 x 5000w, live

TGX20

DSP power amplifier 4 x 5000w, live

  • 4-channel DSP amplifier for live applications
  • Market-leading power density with up to 20kW in 2RU
  • Fully integrated DSP with advanced 96 kHz processing and FIR Drive technology
  • OMNEO integration for seamless compatibility with Dante and OCA
  • Full color touch screen for control without software

SPECIFICATIONS

OUTPUT POWER
Load impedance2 Ω2.7 Ω4 Ω8 Ω
IMD-SMPTE, 60 Hz, 7 kHz< 0.15 %
Maximum Output Power1
All channels driven
5200 W6000 W5000 W2500 W

Number of amplifier channels4
Maximum Output Voltage210 V peak
Maximum Output Current84 A peak
AMPLIFIER
Voltage Gain ref.1 kHz32.0 dB, adjustable 24-40 dB
Input Sensitivity ref. to Max. Output Voltage13.7 dBu (3.73 V), adjustable 5.7-21.7 dBu
THD3 dB below Max., AES17, 1 kHz< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz< 0.15 %
DIM100, 3.15 kHz, 15 kHz< 0.15 %
Crosstalkref. 1 kHz, 12 dB below Max., 8 Ω< -80 Db
Frequency Response ref. 1 kHz, analog into speaker out20 Hz to 20 kHz (±1 dB)
Damping Factor,20 Hz to 200 Hz, 8 Ω> 400
Output Stage TopologyClass D, fixed frequency
Signal to Noise Ratio
A-weighted, analog input115 dB
A-weighted, digital input118 dB
Output Noise
A-weighted, analog input< -70 dBu
A-weighted, digital input< -73 dBu
DIGITAL SIGNAL PROCESSING
Sampling rate48 kHz/96 kHz, OMNEO/Dante synchronized
Signal Delay/Latency
Analog in to Speaker Out, 48 kHz/96 kHz0.70 ms/0.53 ms
AES3 in to Speaker Out, 48 kHz/96 kHz1.00 ms/0.66 ms
Dante Network Latencytyp. 1.00 ms
Signal Processing32/40 bit, floating point
User EQ12 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass & Notch; 2 filters of them with additional asymmetric filter type
User Delay0 to 2000 ms per channel (units: µs, ms, s,cm, m, inches, feet)
Array EQ5 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass, & All-Pass
Array Delay0 to 500 ms per channel (units: µs, ms, s, cm,m, inches, feet)
Speaker EQ10 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Hi-Pass, Lo-Pass, & All-Pass
Speaker X-OverHi-Pass & Lo-Pass per channel, 6/12/18/24/30/36/42/48 dB Bessel/Butterworth,12/24/48 dB Linkwitz-Riley; AlignmentDelay, 0 to 20 ms per channel
Speaker FIRup to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over
Speaker LimitersPeak Anticipation Limiter & RMS/TEMP Limiter per channel
Other functionsSource Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Level Meters, Impedance Measurement, & Load Monitoring
Memory
DSP Presets1 Factory + 20 User
Speaker-Pool Presets30 speaker settings
Source Supervision & FallbackAES3 Lock & OMNEO/Dante network supervision,switch over to alternative Source Selection
CONNECTIVITY
Analog Audio Input/Thru
Type4 x 3-pin XLR female/male
Maximum Input Level+ 24 dBu
Input Impedance, active balanced20 kΩ
Reference level equal to digital input+21 dBu for 0 dBFS
Digital Audio Input/Thru
Type2 x 3-pin XLR (alternative use of Analog In/Thru)
FormatAES3 (AES/EBU)
Input Sample Rates32 to 192 kHz, internal Sample-Rate-Converter
Thru Connectoractive buffered, direct bypass if device is unpowered
Network
Type2 x Neutrik etherCON/RJ45, redundant PRIMARY/SECONDARY
Format1000base-T/100base-TX, integrated switch
Network Audio Inputs8 channels, 48/96 kHz, OMNEO/Dante format
Network Audio Outputs(Monitor)2 channels, 48/96 kHz, OMNEO/Dante format
Front side ServicePort1 x USB Type A
Mains Input1 x Neutrik powerCON-HC
Speaker Output4 x NL4
GENERAL
User Interface
Display320 x 240 pixel, 3.5" color TFT
Front panel indicatorsFull color LED illuminated ring
Front panel operating elementsRotary encoder, Capacitive Touch Screen
Rear panel indicators2 x LED (AES3 Input mode active, Amp-Find)
Rear panel operating elementsMains switch
Power Requirements100 V to 240 V, 50 Hz to 60 Hz AC
Power Consumption
Rated Power Consumption2250 W
1/8 Maximum Output Power at 4Ω2850 W
Idle Mode (no input signal)110 W
Standby Mode< 19 W
Power Supply TopologySwitching Mode Power Supply with digital controlled Power Factor Correction
Protections

  • Dilihat: 4616
  • Brand: Dynacord
  • Product Code: TGX20 DSP power amplifier 4 x 5000w, live
  • Availability: In Stock
  • $0.00

Tags: TGX20 DSP power amplifier 4 x 5000w, live