IPX20:4 4 x 5000 w multi‑channel installation dsp class‑d amplifier

IPX20:4 4 x 5000 w multi‑channel installation dsp class‑d amplifier


IPX20:4

4 x 5000 w multi‑channel installation dsp class‑d amplifier

  • 4 x 5000 W multi-channel installation DSP amplifier with digitally controlled PFC supply.
  • Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive.
  • Dante and OCA integration via OMNEO with fallback options.
  • Parallel, bridged and parallel-bridged drive modes with 70/100V/140V/200V and low impedance operation
  • High efficiency Eco Rail technology for lower operating costs

IPX series are dedicated amplifiers for fixed install application such as e.g. stadiums, arenas, houses of worship, concert halls, theaters and other applications that require high‑power multichannel amplifiers with sophisticated speaker processing. The integrated DSP can run either in 48 kHz or true 96 kHz including FIR Drive. Besides analog inputs also Dante and OCA via OMNEO network inputs are available. Comprehensive fallback options allow redundant scenarios.

Each channel can be individually operated in low impedance mode, or 70V/100V Direct Drive mode. By bridging also 140V/200V Direct Drive is available. By the possibility to parallel two channels and parallel‑bridge four channels all kind of loudspeakers can be driven.

Due to the digitally controlled interleaved PFC supply reliable operation is ensured even under challenging mains supply situations. Reactive current is limited to a minimum, which reduces costs for mains installations and mains fusing in the installation.

In case of idle mode or light mode operation IPX series amplifiers automatically switch to a lower Eco Rail further reducing operating costs. In Eco Mode the amplifiers stay fully functional and supervised.

While IPX series amplifiers are fully integrated in IRIS‑Net, a OLED display on the front panel allows quick local control and supervision of the amplifier.

The connectivity of IPX series amplifiers is optimized for fixed install applications.

SPECIFICATIONS

OUTPUT POWER
Low-Z mode: Load Impedance2 Ω2.7 Ω4 Ω8 Ω
Maximum Output Power¹
Normal Mode, all channels driven5200 W6000 W5000 W2500 W
Bridgen.a
Parallel10000 W8000 W5000 W
Parallel-Bridgen.a.
Direct Drive Mode: Nominal Voltage70 V100 V140 V
Maximum Output Power¹3550 W5000 W5000 W
Number of Amplifier Channels4
Maximum Output Voltage, Normal mode, per channel210 Vpeak
Maximum Output Current, Normal mode, per channel84 Apeak
AMPLIFIER
Voltage Gain
Low-Z mode, ref.1 kHz32.0 dB, adjustable 20.0-44.0 dB
Direct Drive mode33.2/36.2/39.2 dB for 70/100/140 V
Input Sensitivity
Low-Z mode, Max. Output Voltage13.7 dBu (3.73 V), adjustable 1.7-25.7 dBu
Direct Drive mode6 dBu (1.55 V), fixed
THD 3 dB below max, AES17, 1 kHz< 0.05 %
DIM 100 3.15 kHz, 15 kHz< 0.15 %
IMD-SMPTE 60 Hz, 7 kHz< 0.15 %
Crosstalk ref. 1 kHz, 12 dB below Max, 8 Ω< -80 dB
Frequency Response ref. 1 kHz, analog in to speaker out20 Hz to 20 kHz (±1.0 dB)
Damping Factor 20 Hz to 200 Hz, 8 Ω> 400
Output Stage TopologyClass D, fixed frequency
Signal to Noise Ratio Amplifier
A-weighted, analog input115 dB
A-weighted, digital input118 dB
Output Noise
A-weighted, analog input< -70 dBu
A-weighted, digital input< -73 dBu
CONNECTIVITY
Analog Audio Input/Thru
Type2 x 6-pin Euroblock, male
Maximum Input Level+21 dBu
Input Impedance, active balanced20 kΩ
Reference level equal to digital input+21 dBu for 0 dBFS
Speaker Output1 x 8-pin Euroblock, 6 mm, female
GENERAL
Power Consumption
Rated power consumption (see BTU table)2250 W
1/8 Maximum Output Power at 4 Ω2850 W
Idle Mode (no input signal)110 W
Standby Mode< 19 W
Dimensions (W x H x D), mm483 x 88.1 x 514.2
Weight18.3 kg (40.3 lb)
Shipping Weight20.5 kg (45.1 lb)
DIGITAL SIGNAL PROCESSING
Sampling rate48 kHz/96 kHz, OMNEO/Dante synchronized
Signal delay/latency Analog In to Speaker Out, 48 kHz/96 kHz0.70 ms/0.53 ms
Dante Network Latencytyp. 1.00 ms
Signal Processing
User EQ12 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass & Notch; 2 filters of them with additional asymmetric filter type
User Delay0 to 2000 ms per channel (units: μs, ms, s, cm, m, inches, feet)
Array EQ5 filters per channel, selectable as PEQ, Lo- Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass, & All-Pass
Array Delay0 to 500 ms per channel (units: μs, ms, s, cm, m, inches, feet)
Speaker EQ10 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Hi-Pass, Lo-Pass & All-Pass
Speaker X-OverHi-Pass, & Lo-Pass per channel, 6/12/18/24/30/36/42/48 dB Bessel/Butterworth, 12/24/48 dB Linkwitz-Riley; Alignment Delay, 0 to 20 ms per channel
Speaker FIRUp to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over
Speaker LimitersPeak Anticipation Limiter & RMS/TEMP Limiter per channel
Other FunctionsSource Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Pilot Tone Generator & Detection, Level Meters, Impedance Measurement & Load Monitoring
Memory
DSP Presets1 Factory + 20 User
Speaker-Pool Presets30 Speaker Settings
Source Supervision & FallbackPilot Tone supervision at Analog & OMNEO/ Dante inputs, switchover to alternative Source Selection
CONNECTIVITY
Network
Type2 x Neutrik EtherCON/RJ45, redundant PRIMARY/SECONDARY
General1000base-T/100base-TX, integrated switch
Network Audio Inputs8 channels, 48/96 kHz, OMNEO/Dante format
  • Dilihat: 4176
  • Brand: Dynacord
  • Product Code: IPX20:4 4 x 5000 Watt Multi‑channel
  • Availability: In Stock
  • $0.00

Tags: IPX20:4 4 x 5000 w multi‑channel installation dsp class‑d amplifier