Dynacord TGX10 DSP power amplifier 4 x 2500w, live
Bagikan :
Deskripsi Produk
Spesifikasi Produk
Deskripsi Produk
- 4-channel DSP amplifier for live applications
- Power density of up to 10kW in 2RU
- Fully integrated DSP with advanced 96 kHz processing and FIR Drive technology
- OMNEO integration for seamless compatibility with Dante and OCA
- Full color touch screen for control without software
Spesifikasi Produk
OUTPUT POWER
Load impedance
2 Ω – 2.7 Ω – 4 Ω
Maximum Output Power1 All channels driven
2600 W – 3000 W – 2500 W
Number of amplifier channels
4
Maximum Output Voltage
150 V peak
Maximum Output Current
53 A peak
AMPLIFIER
Voltage Gain ref.1 kHz
32.0 dB, adjustable 24-40 dB
Input Sensitivity ref. to Max. Output Voltage
10.7 dBu (2.66 V), adjustable 2.7-18.7 dBu
THD 3 dB below Max., AES17, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.05 %
DIM100, 3.15 kHz, 15 kHz
< 0.15 %
Crosstalk ref. 1 kHz, 12 dB below Max., 8 Ω
< -80 dB
Frequency Response ref. 1 kHz, analog in to speaker out
20 Hz to 20 kHz (ą0.5 dB)
Damping Factor, 20 Hz to 200 Hz, 8 Ω
> 400
Output Stage Topology
Class D, fixed frequency
Signal to Noise Ratio
A-weighted, analog input
112 dB
A-weighted, digital input
115 dB
Output Noise
A-weighted, analog input
< -70 dBu
A-weighted, digital input
< -73 dBu
DIGITAL SIGNAL PROCESSING
Sampling rate
48 kHz/96 kHz, OMNEO/Dante synchronized
Signal Delay/Latency
Analog in to Speaker Out, 48 kHz/96 kHz
0.70 ms/0.53 ms
AES3 in to Speaker Out, 48 kHz/96 kHz
1.00 ms/0.66 ms
Dante Network Latency
typ. 1.00 ms
Signal Processing
32/40 bit, floating point
User EQ
12 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass & Notch; 2 filters of them withadditional asymmetric filter type
User Delay
0 to 2000 ms per channel (units: μs, ms, s, cm, m, inches, feet)
Array EQ
5 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass, & All-Pass
Array Delay
0 to 500 ms per channel (units: μs, ms, s, cm, m, inches, feet)
Speaker EQ
10 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Hi-Pass, Lo-Pass, & All-Pass
Speaker X-Over
Hi-Pass & Lo-Pass per channel, 6/12/18/24/30/36/42/48 dB Bessel/Butterworth, 12/24/48 dB Linkwitz-Riley; Alignment Delay, 0 to 20 ms per channel
Speaker FIR
up to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over
Speaker Limiters
Peak Anticipation Limiter & RMS/TEMP Limiter per channel
Other functions
Source Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Level Meters, Impedance Measurement, & Load Monitoring
Memory
DSP Presets
1 Factory + 20 User
Speaker-Pool Presets
30 speaker settings
Source Supervision & Fallback
AES3 Lock & OMNEO/Dante network supervision, switchover to alternative Source Selection
CONNECTIVITY
Analog Audio Input/Thru
Type
AES3 Lock & OMNEO/Dante network supervision, switchover to alternative Source Selection
Maximum Input Level
+24 dBu
Input Impedance, active balanced
20 kΩ
Reference level equal to digital input
+21 dBu for 0 dBFS
Digital Audio Input/Thru
Type
2 x 3-pin XLR (alternative use of Analog In/Thru)
Format
AES3 (AES/EBU)
Input Sample Rates
32 to 192 kHz, internal Sample-Rate-Converter
Thru Connector
active buffered, direct bypass if device is unpowered
Network
Type
2 x Neutrik etherCON/RJ45, redundant PRIMARY/SECONDARY
Format
1000base-T/100base-TX, integrated switch
Network Audio Inputs
8 channels, 48/96 kHz, OMNEO/Dante format
Network Audio Outputs (Monitor)
2 channels, 48/96 kHz, OMNEO/Dante format
Front side Service Port
1 x USB Type A
Mains Input
1 x Neutrik powerCON-HC
Speaker Output
4 x NL4
GENERAL
User Interface
Display
320 x 240 pixel, 3.5″ color TFT”
Front panel indicators
Full color LED illuminated ring
Front panel operating elements
Rotary encoder, Capacitive Touch Screen
Rear panel indicators
2 x LED (AES3 Input mode active, Amp-Find)
Rear panel operating elements
Mains switch
Power Requirements
100 V to 240 V, 50 Hz to 60 Hz AC
Power Consumption
Rated Power Consumption
1200 W
⅛ Maximum Output Power at 4 Ω
1765 W
Idle Mode (no input signal)
80 W
Standby Mode
< 18 W
Power Supply Topology
Switching Mode Power Supply with digital controlled Power Factor Correction
Protections
Audio Limiters, High Temperature, DC, HF, Short Circuit, Back-EMF, Peak Current Limiters, Inrush Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over/ Under voltage Protection
Cooling
Front-to-rear, temperature controlled fans, supervised
Ambient Temperature Limits
+5 °C to +40 °C (+40 °F to +105 °F)
IEC Protection Class